Honda / Acura K20a K24a Engine Forum banner
1 - 4 of 4 Posts

· M U G E N !!!!!!!!!!
Joined
·
7,219 Posts
Discussion Starter · #1 ·
hey guys, im going to the darkside, and im new to it, i have a 300whp n/a k24/k20, but i want somthing new, i have been reading in the turbo section for like a week now, heres a list i have come up with to get me 600whp,700whp would be even better, add stuff if needed

peakboost turbo kit with a Garrett gt35r need
Bosch 044 Inline Fuel Pump need
bosch 1000cc injectors need
Kpro have
hondata boost vtec selinoid need
rbc and 70mm tb have
k20a2 stg 3 pnp head with valve job have
k24a8 block have but i am sending it out to have blueprint sleeve it
ib pro h beem rods need
9:1 comp pistons, i dont know what brand i want, i have cp's now so i might stick with them need
i know i will need -an fittings and fuel lines, im not new to them, but how many ft will i need to run them from the fuel pump to the fuel rail, and a return line
Aeromotive Compact Fuel Pressure Regulator need
Hybrid Racing K-Series Fuel Rail need i have a bdl now, but i just found the hybrid peice, and like how i can mount the fuel line underneith for a clean look
Aeromotive In-Line Fuel Filter need
will my cc stge 4 clutch be fine for this setup? have
aem boost gauge electric need
aem eugo gauge for my air/fuel need
aem oil pressgauge have
sandwitch adapter plate electronic have

any other stuff im missing,like small things? i know search, but i have been reading alot, and i will continue to read, just want some turbo expert advise all help is welcome
 

· M U G E N !!!!!!!!!!
Joined
·
7,219 Posts
Discussion Starter · #4 ·
Alot of that stuff you have listed is nice, some you don't really need to make 500-600 HP. Your HP goals are not impossible. The right set-up and tuning will render you reliable power with less parts ($$$$).

peakboost turbo kit with a Garrett T3/60-1 w/ .82 a/r need
Bosch 044 Inline Fuel Pump need
bosch 1000cc injectors need
Kpro have
hondata boost vtec selinoid need
rbc and 70mm tb have DON'T NEED THIS
k20a2 stg 3 pnp head with valve job haveCrazy port work is good for NA but not required for Boost, since you have it already cool.
k24a8 block have but i am sending it out to have blueprint sleeve it
ib pro h beem rods need RODS ARE VITAL TO THIS SET-UP
9:1 comp pistons, i dont know what brand i want, i have cp's now so i might stick with them need CP'S ARE GREAT
i know i will need -an fittings and fuel lines, im not new to them, but how many ft will i need to run them from the fuel pump to the fuel rail, and a return line. You don't need much If you already had a 300HP NA motor you should have the fuel system already and the FPR below. Why change it?
Aeromotive Compact Fuel Pressure Regulator need
Hybrid Racing K-Series Fuel Rail need i have a bdl now, but i just found the hybrid peice, and like how i can mount the fuel line underneith for a clean look
Aeromotive In-Line Fuel Filter need
will my cc stge 4 clutch be fine for this setup? have
This clutch is fine for now it handles 250%+ increase in torque capacity

I made 600+HP 400lbs torque on 25psi. Back in 2006 with this set-up.
Stock head
GT35R
Sleeved Block w/ Rods and 9.0.1 psitons
Kpro
1000cc injectors
3.5 bar map

Now unless you want to keep adding parts thats all up to you. Good Luck!


thanks for the help, but i already have the rbc, and i sold my prb intake maifold already so, and no a 300whp na car doesnt need a fuel system, just a fuel rail and rdx fuel injectors, thats what i have now. and you wrote a comment next to the ib pro h beem turbo rods, where you saying that they are fine, or are you saying there vital and i should get better rods? i have ib rods now, but there the i beem rods for na, i would think there h beam turbo rods are fine
 

· M U G E N !!!!!!!!!!
Joined
·
7,219 Posts
Discussion Starter · #6 ·
If you have the mani and TB already then sweet. Your rods are fine. There are a few set-ups that are on a stock motor pushing 550-600WHP so your ok even with those IB rods.

My fuel system was just a walbro 255, aeromotive FPR. 1000cc injectors and steel braised lines in the engine bay only (feed and return) Good Luck.
i want to run braided lines all the way to the fuel tank
 
1 - 4 of 4 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top