Honda / Acura K20a K24a Engine Forum banner

1 - 20 of 20 Posts

·
Registered
Joined
·
1,016 Posts
Discussion Starter #1
Is there an aftermarket intake that will work with a k20 / "EG" swap, or will i just have to fab something myself?
 

·
Registered
Joined
·
929 Posts
I just ordered the prototype racing intake with filter for 157 shipped.
 

·
Registered
Joined
·
929 Posts
yup thats the one. Im hoping to get the motor in within 2 weeks depending on when the kit comes in for install. Then I can tell you the fitment of it. It looks like it should fit without any problems.
 

·
Registered
Joined
·
929 Posts
That's the one in ?.

Very eager.

Where are you at?

Im in Virginia.
 

·
Registered
Joined
·
929 Posts
Im just waiting on the kit for install and parts that were missing from the swap purchase.

Once I get that just needs to be installed. Im ready once parts get here.

The Right Coast...LOL..
 

·
Registered
Joined
·
59 Posts
supafly said:
Im just waiting on the kit for install and parts that were missing from the swap purchase.

Once I get that just needs to be installed. Im ready once parts get here.

The Right Coast...LOL..
That intake will work..nicely
 

·
Registered
Joined
·
10 Posts
K20EG said:
supafly said:
WOOHOOOOOOOOOOo Approved by the man himself...
till i have my own :p
It would be much cheaper to make your own and since it's literally just a straight tube, I can't see any kind of drop in performance from a DIY. If it were a cold-air design I'd definately be ready to get it, but I'll stick to a K&N cone filter and a length of tubing, thanks 8) .
 

·
Registered
Joined
·
59 Posts
Archidictus said:
K20EG said:
supafly said:
WOOHOOOOOOOOOOo Approved by the man himself...
till i have my own :p
It would be much cheaper to make your own and since it's literally just a straight tube, I can't see any kind of drop in performance from a DIY. If it were a cold-air design I'd definately be ready to get it, but I'll stick to a K&N cone filter and a length of tubing, thanks 8) .
Yea ...I got the cold air intake for EG dialed in...i have yet to dyno test it :)
 

·
Registered
Joined
·
929 Posts
Rec'd the intake today.

Its only the end piece that fits inside the filter and the filter.

The filter has about a 6-8 inch diameter. Its friggin HUGE.

I still have to get a straight pipe welded together from the throttle body.

I can post pics if anyone is interested.
 

·
Registered
Joined
·
182 Posts
Who's mount kit is that on the yellow eg?
Those billet mounts look nice.

Also K20EG........when are u going to release your line of cold air intakes and header?
any prices u can throw out for you cold air intake and header?
Or would it be good to modify a cold air intake from aem or injen?

thanx
 

·
Registered
Joined
·
182 Posts
Uberhatch said:
that car has hasport mounts
are those a 1-off set just for that car or is that something they are going to go in production with?
thanx
 

·
Registered
Joined
·
182 Posts
supafly said:
http://www.k20a.org/upload/DCP_0593.JPG

http://www.k20a.org/upload/DCP_0592.JPG

If these are not good enough let me know and Ill get closer pics.
man
the whole thing just looks beautiful in there!
i like the way the motor looks like it just belongs there.
im assuming those are the mounts from k20eg right?
i need to get me a damn K series swap started already!
anyways looks good bro and keep up the good work.
btw....you take you car down the track yet for some 1/4 mile times?
thanx
 
1 - 20 of 20 Posts
Top