Honda / Acura K20a K24a Engine Forum banner
1 - 14 of 14 Posts

18 Posts
Discussion Starter · #1 ·
CAR IS LOCATED SAN DIEGO CALIFORNIA. No, it does not pass emissions, nor will it ever unless you go a shady route. Hence the reason for selling the car, now in other states the emission laws are much more lienient, allowing them to register this vehicle legally.
VIN upon request for serious inqueries only. Those interested please PM me vs posting in the thread waiting for a reply. Either is fine, but PM will be faster.

price reduction

Tossing the offer out to K20A.ORG first, before it hits ebay
updated pictures soon!
-1993 Civic Si
-Silverstone Metallic paint from an S2000( some paint imperfections )
-Clean body no dings or dents
-Red/Clear tail lights
-Mercedez s500 HID ballasts and bults
-Black housing headlights(w/ city light)
-Amber Corners
-JDM OEM sidemarkers
JDMSH!IT c/f duckbill
Casper shields for HIDs
Recently replaced rubber roof liners
Rear splash gaurds
-Stock Si Interior
-Type-R CD player(lights up amber)
-JDM EG6 cluster reads approx 70,XXX
-Honda optional console(without DINS)
Spoon Shift knob(w/o spoon logo on top)

2002 JDM Integra Type-R motor(16,000 on the motor)(5,500$)
6 speed close ratio tranny
220BHP, 143 TQ(stock specs)
204 WHP 145 TQ(to the wheels)
Custom Equal length 4-1 header(600$)
Apex'i VAFC2(tuned by hookups)(300$)
TODA ecu
AEM Short Ram Intake(120$)
Aeromotive Fuel pressure regulator(80$)
AEM Fuel rail(120$)
Glycerin filled Fuel pressure gauge(50$)
Bonnaco fuel lines(100$)
HASPORT stage 2 axles(450$)
GAB suspension(1,500$)
CTR 5 lug conversion(1,000$)
OEM 2001 S2000 wheels(900$)
Khumo 711 times(almost new)
New front brembo blanks(80$)
New axxis metalmaster pads(65$)
JL Audio XR650csi Speakers w/ 3 way crossovers(250$)
New driver side door seal(50$)
New back window seals(50$)


right click save as.


865 Posts
I would be willing to give you $10K plus a EK shell No motor but will include the GSR Blades....GSR CLUSTER.....OEM CTR DOOR PANELS.....NEW FRESHLY PAINTED BLACK EXTERIOR, painted back in MAY of 05 and has been in storage since then, Also have OBD2a VTEC engine harness form a b16 that will fit any B-series motor. If using on a B18c, will have to add a few wires. Car has never been stolen. My email is [email protected] if you are interested.

15 Posts
im in the des plaines area. right now i have an itr motor(about 40k mi) in my eg hatch with jun headers,test pipe,tanabe exhaust,vafc,act stage 2 clutch, and its chipped. BEST 1/4 TIME: 13.5(and that was with a bad launch and a mishift) :mad: as for the car their are minor dents and of course the rust on the rear quarter panel.thats my 1st car and i love it but i want something with more power.(dont get me wrong i love my car right now but id love it even more with a k series all motor setup. but yea, please reply asap.thanks man.peace
1 - 14 of 14 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.