Honda / Acura K20a K24a Engine Forum banner
1 - 20 of 51 Posts

· Registered
Joined
·
576 Posts
Discussion Starter · #1 ·
well,i'm looking for 3" exhaust for my K25 EP3,but i want a quite exhaust for daily drive...

what can i find?

i think take a ASP exhaust pipe kit(DIY kit) with a Magnaflow muffler.

what do you think abour it?

do somebody have video of 3" exhaust on EP3?not boosted please:eek:
 

· Registered
Joined
·
383 Posts
Get the 3" piping and the OBX 3" Twin Loop Muffler.....quietest 3" exhaust....I have it on my ep3 and it sounds great and its a quiet
 

· Registered
Joined
·
576 Posts
Discussion Starter · #3 ·
Get the 3" piping and the OBX 3" Twin Loop Muffler.....quietest 3" exhaust....I have it on my ep3 and it sounds great and its a quiet
have you got pics&videos please?
the OBX muffler,is it good for high performance?:eek:

for the piping?ASP,Kteller?

thanks for your answer:up:
 

· Registered
Joined
·
8 Posts
have you got pics&videos please?
the OBX muffler,is it good for high performance?:eek:

for the piping?ASP,Kteller?

thanks for your answer:up:
The OBX twin loop is great i have the 2.5 on my ep3 it sounds great looks great and my butt dyno felt a difference i love this muffler and its only 95 bucks shipped on ebay i think everyone should get one :D
 

· Registered
Joined
·
576 Posts

· Registered
Joined
·
3,192 Posts
It will come down to restriction. The more restriction, the quieter the set up.

So it will be up to you on how much hp you are willing to let go to have a quiet car.
 

· Registered
Joined
·
3,192 Posts
If you are on a budget then get the kteller or vrs, but I can tell you from experience that their kits suck point blank.

The quality of bends and finishing is not near what I provide with my bends.

I recentlly installed a kteller pipe kit on a prelude and it was pure pain in the ass, because the bends were not on par and the swaged ends were so loose that it might as well not been there.

But its up to you on what you want to do.
 

· Registered
Joined
·
284 Posts
If you are on a budget then get the kteller or vrs, but I can tell you from experience that their kits suck point blank.

The quality of bends and finishing is not near what I provide with my bends.

I recentlly installed a kteller pipe kit on a prelude and it was pure pain in the ass, because the bends were not on par and the swaged ends were so loose that it might as well not been there.

But its up to you on what you want to do.
the kits you make a very nice. would you happen to make them for ep3??? by the way my vrs kit fit perfect in my ep3.
 

· Registered
Joined
·
3,192 Posts
I have ep3, dc5, em2, ef, eg, ek, dc2 kits.
 

· Registered
Joined
·
576 Posts
Discussion Starter · #15 ·
It will come down to restriction. The more restriction, the quieter the set up.

So it will be up to you on how much hp you are willing to let go to have a quiet car.
for the moment,i've got a very restrictive 2.5" catback on my K25(270WHP),and it's very very quite!

i can accept a more louder but not too much!

so i have to put a 3" pipe with a resonator and a muffler!

so Magnaflow and OBX twin loop are good for my aim!

and,of course,it will flow more than my 2.5" restrictive exhaust?

what about vibrant muffler&resonator?

onefstek,how much is your EP3 kit?can you make it for EUDM spec(for the lenght i say)

have you pics?what about the Mandrel etc...?
 
1 - 20 of 51 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top