K20A.org .:. The K Series Source . Honda / Acura K20a k24a Engine Forum - Search Results
Showing results 1 to 25 of 500
Search took 2.76 seconds.
Search: Posts Made By: CAFROG
Forum: General K-series related talk 09-01-2018, 06:23 AM
Replies: 8
Views: 342
Posted By CAFROG
Re: Removing K20 from RSX ready to swap into EG

Karcepts hubs. http://www.karcepts.com/shop/product.php?id_product=53

The advantage of using the whole K24A2 is not needing to do the head swap right now. The K24A2 head isn't better....it flows...
Forum: General K-series related talk 08-31-2018, 04:13 PM
Replies: 8
Views: 342
Posted By CAFROG
Re: Removing K20 from RSX ready to swap into EG

Also, you have to mount the shift box. Either on top and run the cables through the firewall or cut a big hole and buy an aluminum cover. Race car style goes through the firewall with one of them...
Forum: General K-series related talk 08-31-2018, 04:09 PM
Replies: 8
Views: 342
Posted By CAFROG
Re: Removing K20 from RSX ready to swap into EG

Use your shift box and cables if you want to save cash. But their aluminum shift box is pretty sweet. If you plan on drag racing I would suggest using your type S axles and replacing your hubs. It...
Forum: General K-series related talk 08-29-2018, 08:01 PM
Replies: 8
Views: 342
Posted By CAFROG
Re: Removing K20 from RSX ready to swap into EG

Complete engine, engine harness, transmission, shift box, shift linkage, ECU, axles.

Can't use those axles unless you get a set of hubs that will accept the axle. I have a set of Karcept hubs on...
Forum: All Motor K series Technical Discussion 08-18-2018, 08:37 AM
Replies: 21
Views: 1,457
Posted By CAFROG
Re: Cheaper to build or buy OEM?

In terms of a USDM K20A2, they're well over 10yrs old and will have more mileage/wear then a JDM version. A USDM version could've been "rode hard and put away wet". Not that it means don't buy the...
Forum: All Motor K series Technical Discussion 08-12-2018, 07:21 PM
Replies: 21
Views: 1,457
Posted By CAFROG
Re: Cheaper to build or buy OEM?

If you enjoy building motors or would like to experiment and learn how to build motors, abuilt K is a good option. But if you plan on having somebody else build it for you, I would stick with the...
Forum: Parts for sale 08-05-2018, 02:58 PM
Replies: 5
Views: 959
Posted By CAFROG
Forum: Forced Induction and Nitrous K series discussion 08-02-2018, 05:50 AM
Replies: 10
Views: 976
Posted By CAFROG
Re: injector size question

Based on what guys do to their cars and multiple tuners I'be spoken to, the stock fuel lines would be okay but not optimal....especially for 600+whp. But I think stock lines are okay for 400-500whp. ...
Forum: Engine Building 07-31-2018, 01:09 PM
Replies: 763
Views: 53,642
Posted By CAFROG
Re: You want to win up to $50? The 86.5x86 rebuild question!

Same build thread from 2015? Same motor build or re-do?
Forum: General K-series related talk 07-23-2018, 11:24 AM
Replies: 2
Views: 917
Posted By CAFROG
Re: Help with knocking/ticking noise

Sounds like valves in second video. Kinda normal sounding VTEC idle to me.
Forum: ECU and Tuning 07-14-2018, 06:50 PM
Replies: 38
Views: 1,276
Posted By CAFROG
Re: K24 falling on face not getting fuel?

If you're in a hurry, a basic printer cable works perfect.
Forum: ECU and Tuning 07-12-2018, 09:41 PM
Replies: 38
Views: 1,276
Posted By CAFROG
Re: K24 falling on face not getting fuel?

I thought he was referring to the Throttle Positioning Sensor (TPS)
Forum: ECU and Tuning 07-12-2018, 02:29 PM
Replies: 38
Views: 1,276
Posted By CAFROG
Re: K24 falling on face not getting fuel?

At low speeds it jerks.....that's what I figured. What if you're more aggressive with throttle at takeoff? Ride the clutch a tad more. I am guessing no partial throttle tuning was done.
Forum: ECU and Tuning 07-11-2018, 11:20 AM
Replies: 38
Views: 1,276
Posted By CAFROG
Re: K24 falling on face not getting fuel?

Any CEL codes?

If it falls on its face jerking....what's the speed you are going when it finally dies? Is it jerking at low speed and then jerks until it dies? I guess I'd like more detail about...
Forum: ECU and Tuning 07-10-2018, 07:59 AM
Replies: 38
Views: 1,276
Posted By CAFROG
Re: K24 falling on face not getting fuel?

Jerks at partial throttle? Like 1st gear cruising in a parking lot? If so, I venture to say the problem in the tune. Maybe no partial throttle tuning done? My car tends to do a jerks at partial...
Forum: General K-series related talk 06-13-2018, 07:02 PM
Replies: 14
Views: 1,183
Posted By CAFROG
Re: human dog face

Sad. I check in a few times a week. I don't like other platforms for Honda information.
Forum: 2001+ Civic EP3 / RSX DC5 / EM2 06-06-2018, 02:41 PM
Replies: 1
Views: 598
Posted By CAFROG
Re: K20R en route.... what am I missing?

The Type R swap is JDM...aka right hand drive. If you are left hand drive...the engine harness will be short because it is designed to go through the firewall on the opposite side. I was able to make...
Forum: 1992+ Civic EG / DC2 / EK K-Series Swap 05-07-2018, 03:18 PM
Replies: 4
Views: 824
Posted By CAFROG
Re: K20z3 eg idle surging and starting problems

Kpro? If so....the basic tunes they have available (online) should rule out tune issues causing surging idle.

I figure a rule of thumb for MAP placement.....if the TB you're using has a spot for...
Forum: 1992+ Civic EG / DC2 / EK K-Series Swap 05-03-2018, 03:43 PM
Replies: 4
Views: 824
Posted By CAFROG
Re: K20z3 eg idle surging and starting problems

Just to be sure.....on the IACV.....can you take it off again and check to see if the cylinder inside will spin with your fingers? Mine looked clean too (no CEL)....but that cylinder should spin...
Forum: 1992-2000 Civic / CRX / Integra / Del Sol 03-30-2018, 12:10 PM
Replies: 234
Views: 49,248
Posted By CAFROG
Re: CAFROG's EH3 K20A Swap

Just noticed your post. Life is good.

Ran 12.72 (and 12.75) @111mph on the 205 drag radials about 3 weeks ago.

New mount inserts (stiffest poly that Hasport uses). Had to float my drivetrain...
Forum: Drag Racing 03-21-2018, 02:33 PM
Replies: 432
Views: 92,521
Posted By CAFROG
Re: Official Registry: K series 1/4 Mile Quickest All Motor Times On DOT Street Tires

12.72 @ 111mph. (2.1 60ft....yuck)
EH3 (1992 EG Si)
Stock block K20A w/RBC IM
ASP budget header
3" exhaust (resonator and muffler)
3" intake w/velocity stack
Kpro tuned at 227whp 165tq on pump...
Forum: 1992+ Civic EG / DC2 / EK K-Series Swap 01-15-2018, 08:20 AM
Replies: 8
Views: 1,864
Posted By CAFROG
Re: Over Heating problem k24a2 ek HELP!!

"My heater is set all the way to red and turn off my speed.
Things i have done: Raise the front high off the ground, threw my Lisle funnel and massage the hell out of the lower hose while car is...
Forum: 1992+ Civic EG / DC2 / EK K-Series Swap 01-01-2018, 06:18 AM
Replies: 21
Views: 2,284
Posted By CAFROG
Re: K20z3 EG hatch dosent start please help :(

Fuel pump primes so that means the main relay should be fine.

When doing imm. bypass on kpro....you uploaded it to the ECU? (Up arrow)

Check all connections used for conversion harness
Forum: 1992-2000 Civic / CRX / Integra / Del Sol 10-01-2017, 05:34 PM
Replies: 234
Views: 49,248
Posted By CAFROG
Re: CAFROG's EH3 K20A Swap

Let off early and still broke out. Best time so far. Bolt on tune with 205 street drag radials.

https://youtu.be/PXLLcT5NpyQ
Forum: K-Series Transmission 09-13-2017, 05:50 AM
Replies: 30
Views: 2,388
Posted By CAFROG
Re: 6 speed mechanical lockout info please

Cool. Good luck in your adventure!
Showing results 1 to 25 of 500

 
Forum Jump


All times are GMT -8. The time now is 05:58 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
 

Garage Plus vBulletin Plugins by Drive Thru Online, Inc.